Tinycontrol

HARDWARE:

– 4 analog inputs with switched amplified gain, measurement range from 1mV to 33V. Can be used for voltage, AC/DC current (need additional sensors), analog temperature sensors, photoresistors as dusk sensors, pressure sensors and many more, 

– 2 direct analog inputs up to 3.3V, for DC voltage/ current measurements, 4-20mA sensors and many more,

– 1wire digital bus: support up  to 6 temperature DS18B20 sensors,

– I2C digital bus (common with 1wire on RJ12 socket) for many different sensors: temperature, humidity (and pressure) BME280, AM2320, for remote OLED displays, for RTC and more, *

– serial bus (UART 3.3V)  at this moement support CO2 sensor, PM2.5/PM10 dust sensor, GSM module and Duraluxe PV inverter, *

– 4 logical inputs: as a status monitor (open/close door, PIR sensors etc), as button for manual swithcing and bistable option or as a pulse counter from an energy meter,

– 1 relay (NZ, NO, C),

– 1 transistor output, give power voltage  on terminals,  for  loads up to 1A,

– 4 outputs of  OC standard for switching relays, transistors, etc,

– 4 PWM output 50KHZ to 100kHz,

– supply voltage and temperature on board measurement.

SOFTWARE:

– modern web interface, pull-down menu, javascripts,

– user configurable website -simple way by switching on/off visible elements and  location arrangement on Status page

– user configurable website –  advanced way  by generating own javascripts to fit website apparance,

–  possible download picture to Status window,

– login as admin or user to see only Status page,

– remote control one to many devices by UDP, very usable to button over network implementation,

– event config with 2 conditions analysis – as simple automatisation,  

–  scheduler for setup up to 50 time events,

– support for many communication protocols: SNMP, HTTP GET/POST and MQTT,

–  many option for setup or control  by http request from outside device or sending http command from controller to other devices,

– free for non commercial usage cloud mqtt.ats.pl for collecting data and drawing charts from sensors value.

– reading data via  MODBUS TCP  by PLC controller;

–  many additional features on cloud like events, scheduler, SMS gateway – also for communication between different devices*

– mobile application,

LIST OF SUPPORTED SENSORS AND DEVICES:

Analog inputs: all range of voltage output  or 4-20mA output sensors, supported by firmware:
– AC voltage sensors (AC-meter,TR-12);
– AC current sensors : SCT013-000, SCT-013-03;
–  DC current sensors: ACS711EX_15, ACS711EX_30, ACS709_75, ACS711LC_12, ACS711LC_25, ACS711LC20, WCS1800, LA100P, R=0.1ohm, R=0.01ohm, R=0.05ohm;
– high DC voltage sensor DC (for  PV, under development);
– temperature sensor : PT1000 (need additional resitor);
Logical inputs  (digital):
– open door/window magnetic sensor or similar;
– energy measurement from pulse output of energy meters:
1wire bus: temperature sensor DS18B20;
I2C bus:
– humidity sensors: BME280 (humidity, temperature, air pressure), AM2320(humidity, temperature);
– particulate matter sensor PM -SPS30 (PM1, PM2.5, PM4, PM10);
– display OLED 0.96″;
Serial port:
– GSM module;
–  SPS30, SDS-011 particulate matter sensors ;
–  CO2 sensors MH-Z16, MH-Z19;
– PV Duraluxe inverter;
– ultrasonic distanace meter;
– 2D and barcode scanner;
–  RFID readers*:
MODBUS port (by RS485 converter):
– 2- 2 direction energy meters SDM120M and SD72D-M (read power, energy, voltage, current, phase and other parameters – depend on meter model);
– prof sensors of water parameters:  RDO-PRO-X:

MODBUS TCP – PCL controller can read sensors connected to Lan Controller (tested with Siemens LOGO).

*option under development and new function will be available.